TTS-10 PRO 10000mW Laser Engraver Machine Usongshine 12Pcs DIY Unfinished Wooden Tool Engraving Machine for Usongshine Nema 17 Stepper Motor 42BYGH 500mm Honeycomb Laser Bed (10W)

Works great. Good value.

I received my engraver 10 days ago and finally got it going today. It came very well packed and you could tell it was a quality product upon opening it. There was everything you would need to assemble it and get it going. The enclosed software was unreadable but It was easy to find and download. The instructions are adequate, but brief. Here is what I found in assembly and testing. *Read the instructions carefully and carefully follow. *Be especially careful in adjusting the POM wheels. If they are too tight, the movement is jerky. *Don't get confused with the X and Y! plugs on the left side. I got them backwards and it took 3 emails to support before I finally figured out what was going on. *Email to support is answered withing 24 hours. Response came at 1 or 2 am the day after I sent my request. Once I got the XY correct, and the POM wheels adjusted, I could tell that I had it correct because when I used the Jog errors on the software, the Laser moved smoothly to the left, right, forward, and back. You can see in the power and speed test picture that at full power and slow speed it burns thru the first layer of 1/4" plywood. I recommend that you get the air pump as it can create a lot of smoke, and you should also have good ventilation. I don't think you can get a better 10W laser anywhere for the price.

Have been using for over a year now, holds up to my cleaning, and the holes have not stretched out at all. If this one ever does get bad I'll definitely be getting another one!

Introduction I purchased the TTS-10 PRO because I am a graphic designer and wanted to engrave some wooden plaques and different materials. After using it for several months, here’s my honest take. First Impressions Initial Feel: Lightweight, not very sturdy Setup Experience: Not the easiest, but it can be done with a little work. Pros ✅ Does what it is supposed to ✅ engraves wood no problem Cons ❌ Doesnt engrave glass ❌ tough to get set up ❌ Not the most sturdy and moves around when it's on. My Detailed Experience I have been using this for a few months, and the program used to engrave is not the easiest to navigate. It does have a decent learning curve to it. The machine does shake quite a bit when it's being used. Final Verdict—Would I Recommend It? Yes, but if I was only engraving flat wood products.

Works great easy to use.

I took apart a marine KVH satellite dish radome which contained a couple of stepper motors. I wanted to be able to use it as an antenna rotor. This driver and an Arduino Uno was all it took to get the azimuth stepper motor rotating to any position. And a good excuse to find out more about stepper motors. Fun project. Just Google "Arduino Stepper Motor" to get ideas on how to write the sketch.

Bought this machine Jan 6th, it took a few weeks to figure it out. Used it for 3 days. Made a few small projects and the laser stopped burning. Replaced the product for a new one, worked about 4 days and the laser stopped working AGAIN. I'm the processes of returning and ordered a different brand this time. I do not recommend this machine

I use this to drive a stepper motor used to control water flow. Instructions were straightforward and it was great being able to set output current and steps per rev. Controlling flow to about 1% beyond the flow sensor resolution. Commands come from an Arduino.

Très bon matériel

Heavy magnetic honeycomb and a perfect fit for a Creality Falcon2 Pro Laser 40w.

As advertised and fast shipping, haven’t tested them yet but all seem well packaged and in great shape.

Note: Try not to buy motors separately, I bought this to complement another stepper motor for a project I was making and it turned out the interal wiring was different which made troubleshooting the wires with their separate drivers more annoying than usual. Outside of that, great, cheap product that worked a-ok.

Some manipulations are needed to fix corner plastic parts in their places (for example with double side tape) and add anti-slipping under aluminum plate to make it fixed (single side rubber tape).