Genie Screw Drive Coupler 30257T, Black

use a very cheap price to fix your own genie garage door. If your motor sounds but cannot open the door please do try to change this coupler.

Coupler was a very inexpensive way to save my automatic garage door opener.

Good work perfectly on my Genie screw drive pro garage door opener it is a 2 person job and beware off the cableI recommend start getting out the way the cable and them just loose the screw and both end woth one person on the opener and the other holding the othe ends take the screw off take a needed pliers and take out the coupler if is stock on the opener then put the new and make sure the alignment don't forced take your time when is in place screw back up and make sure before you tested that the stop sensor are working correctly it is simple to tested just someone to click the opener button and simulate the door pushing the sensor if the door stops is fine if is not that is a problem for me mine for some reason was disconnected and that damaged the coupler but a fixed and is working perfectly fine hope thos help someone good luck

Genie Garage door opener

This was not my issue. The original one lasted more than 25 yrs…. But, since I rebuilt the other components I did the entire drive train. Should be good for another 25 yrs with the old pc as a spare!

Garage door opener not lifting door screw drive chattering. Ordered coupler, Genie lube, and trolley assembly. After watching some pitiful you tube video's I determined that the coupler was the big problem but the trolley should also be replaced. there was no good video on how to replace it just where it was.The coupler fixed my problem and was of the same quality as the original hope I don't but would buy it again. The original lasted 18 years and know the reason it went bad. Three things to be aware of and check every year (1) the garage door limit switch clean the contacts (this was my problem they were dirty and allowed the motor to keep turning and damaged the coupler) there are two of them. (2) the garage door is balanced as per manual if the spring breaks or becomes too weak it will become difficult for the Genie to lift the door and wear out the coupler or trolley. (3) make sure the rail assembly and screw drive are clean and well lubed.

The coupler worked like a charm.My issue first popped up when the screw drive seemed to be jammed. I looked at the collars between each section and they seemed to be in good shape and then I came across this part. Before I ordered it I went ahead and removed the old one just to make sure it wasn't something else. Here is a quick trick, you need a tall ladder or an extra person. I did mine solo and with a little planning of tools needed(ratchet set, needle nose pliers, regular pliers) it went pretty quick. You have to remove 4 nut/bolt combos to get to this part. The first to are on the track closest to the motor head. The second are the bolts that connect the motor head to the ceiling mounting bracket. Once those are removed, wiggle the motor head away from the track and you will see this coupler. You will need to use a pair of needle nose pliers to get it out and make sure there is nothing else in there. My coupler was bored out on one side and fine on the other. I also used the needle nose to remove the small plastic shavings left behind from the damaged coupler. Install the new part into the motor and then using your needle nose pliers adjust the position of the end of the screw drive to get it lined up. You can then bolt everything back together. This should take care of the issue. If it doesn't, you might need to adjust the small dials to the right of the track on the unit itself. I took each of mine a quarter turn clockwise and the unit runs smooth.

I apparently neglected greasing the worm gear on my nineteen year old Genie garage door opener for a bit too long. When very cold weather hit it apparently seized enough that the coupler between the worm gear and head unit failed. These are plastic with an outer steel jacket and are designed to break away if the door hits something unmovable and the safety reverse function fails, a sort of double fail safe device. Installation took about thirty minutes but I am mechanically inclined. Installation requires separating the worm gear rail and the head unit but I installed this unit initially, so it wasn't particularly intimidating. The best five bucks I've spent in several years. Should the door refuse to move when the button is pushed but the motor is running, there's about a 90% chance this part is the culprit, especially if a grinding noise is hear and the door appears to be attempting to move intermittently.

It got the door opener working again in 15 minutes, a simple fix.

For a year, my garage door opener wouldn't work. Replaced this part and it works like a charm. It turns out that this part breaks intentionally if there is too much stress on the system... re-aligned tracks and had everything serviced. Good to have a spare one of these on hand.

I am happy with the part that I received, no complaints

Exactement comme annoncė

Work perfect no regrets