FOCEAN Boat Flooring EVA Foam Boat Decking Faux Teak Marine Flooring Boat Mat Boat Carpet Sheet for Motorboat RV Yacht Kayak Surfboard, 94.5"x 47.2"/35.4"/23.6"/15.7"ClimeCo Certified

The media could not be loaded. Not only does this fake teak marine mat provide an air of refined sophistication to the cabin, but it also offers a number of useful advantages that have significantly elevated the quality of my time spent on the water. To begin, the standard of excellence achieved by this boat flooring is very remarkable. The EVA foam substance is hardy, pleasant to the touch, and offers outstanding traction all at the same time. Even when it's rainy, I am able to walk with complete assurance on the deck without sliding. During extended boating journeys, the foam padding provides an additional level of comfort, which helps reduce feelings of weariness. The boat flooring EVA foam boat decking provides a pleasant and secure platform for all of my activities on the boat, including sunbathing, fishing, and hosting guests. One of its most notable qualities is the imitation teak style it has. The inside of my boat benefits from having a touch of refinement thanks to the grey color with black lines that imitates the traditional appearance of teak wood. It is astonishing how much attention to detail was put into the creation of this product, which has wood grain patterns that are true to life and textured surfaces that simulate the surface of genuine teak. My boat receives an immediate boost to its visual appeal thanks to this flooring, which also helps to create an inviting and opulent ambiance.

Looks awesome on the boat and makes the floor not slippery. Also makes it look very fancy. Everyone will complement your boat if you get this washes off easy sticks well takes a few hours to put in.

used it on my patio

Just finished installing the product so don't have any long term durability info yet but thought I would share what I learned. A major part of the success of your project will come down to how A) How well you prepared your surface for a good adhesion. and B) How well you measured and made your templates. The cockpit of my boat was previously painted so I sanded and freshly painted my entire cockpit with topside paint a few weeks before install time. And then on the day of install just went over every section really well with acetone to make sure their was no grease or dust before I applied. And as far as measurements go. well every persons project will be different but don't rush this step. It is very important. Think about where you will need to make breaks due to boat layout or due to the size of the material all while making it look like that is how it was meant to be. Draw out your space on paper with measurements and think about how much material you will need to complete your project. I suggest buying an extra roll more than you think you will need to be able to fix pieces in the future but also because UNFORTUNATLY this product is made so the rolls do not end on full boards. (This cost them a review star) And a few of my rolls were not even cut straight. So there was more waist than would be otherwise. When making templates. Think about how you will make all your lines line up throughout your entire project to make it look like it all flows visually. I made templates on a roll of paper. I had textured edges in the fiberglass of my cockpit about a 1/2 inch back from the edge of each section where the non skid was. so I rough cut the piece to fit and taped in place then went over with a stick of artist graphite rubbing around edges to get an exact line on the paper where my edges were. I would also measure out and draw in 1/2 inch variances around objects that will need to be varnished in the future so I can still have room to get in there to tape, sand and varnish. also around any water fill caps or fuel fill caps, hatch hinges etc. Everyone's layout will be different but think about future maintenance and usability. Also in my opinion having the border space around everything looks really good and having the edge of the product back from the edges will keep it from getting caught on things and peeling up. I also took exact measurements of gaps between pieces to help me to be able to lay out templates later at home and in order to have all lines on the EVA Flooring line up perfectly. So you have to account for all space between each template section. In other words. Slow down and really put on your thinking cap on and give yourself all the necessary information in order to properly layout your job later on your material if you want straight flowing lines throughout your floor. It was not always so easy or obvious how to accomplish this in complex shaped areas. I drew pictures of the floor layout and assigned a letter and signified port or starboard. I did this to each section on my drawing and put a piece of painters tape with corresponding letter on each section of the boat and on each paper template section as well as each piece of EVA Flooring when cutting out. I had to do this to keep things organized. This really helped me throughout project because when you have a bunch of similar looking pieces later on if I did not have everything lettered I would have been overwhelmed and confused for sure. Ok, so once templates were all cut out I would go back and then I would dry fit the templates to make sure I did not mess up anything. Measure many times and only cut once. Ok so moving on I took the EVA Foam Decking out of the box and laid them out flat in my driveway in the sun and put weights on them to relax the material as best I could and get it to lay flat. I saw other reviews saying the product could shrink so I figured I would listen and just set them out for the day to be safe. This helped flatten them out and made much easier to cut. So I then cut all the pieces out. I made rough measurements and cut large rolls down to more manageable sizes and then traced my templates exactly and cut out. I had lead 1lb. fishing weights and water bottles on EVA material as well as my templates while cutting out to hold template down smooth as well as flatten EVA material out as much as possible to make accurate cuts. After I cut out I used a bottle cap to draw rounded edges on all corners for a more finished look and then cut those off. Then once that was finished I carefully went around all edges with the edge of a orbital sander with 100 grit paper to bevel edges to match the factory finished board edge look. I then went back around with 220 grit to smooth out to finish. I suggest practicing this on some scraps before doing on your final product. It takes a little finesse but well worth the time. Once this is done I was ready for install. (I saw many reviews suggesting additional adhesive. I personally felt the tackiness of test pieces I tested out made me feel that with proper preparation of my particular surface that it would be ok to install without any additional adhesive. Not to say the other reviewers are wrong at all. I just made that judgement call for myself and my particular application surface and level of surface preparation. That being said. Time will tell. But this is what I did.) So... I went down to my boat in the harbor and wiped all surfaces with acetone and dry fit my first piece. I used one gallon water jugs as weights to help hold pieces in place. once they were exactly where I wanted them I would lift up half leaving the weights on the other half or have a helper standing on it and then I would take a Exacto knife and lightly slice the bottom paper backing. A very shallow cut just through the paper. I would then peel off that half the backing and lay down straight with a vinyl floor installation roller or a paint roller with foam head. Something to roll the pieces down and push all the air out as it is being laid down. Then I would go over it really thoroughly pushing from the center to the outside making sure all air is out and all material firmly pushed down. Then I stand on the other half and peel off the other side of the paper and repeat the process. Making sure that everything gets laid down right to the edges and that all my reveals are perfectly straight. I did this until all pieces were laid down. You could do this alone but I suggest getting a helping hand. Preferably someone with some patience because once this stuff sticks down it is not coming back up. It is really sticky. You can lift small sections back up in an emergency as you are applying before any roller weight has been applied but be very careful. You get one shot so have everything perfectly lined up before any paper backing comes off and make sure If someone is standing on one side to help hold in place just make sure they don't move at all. So any children helpers is a bad idea. lol Anyway, Once all your pieces are completely down you are done. After that I would just walk all over installed pieces with bear feet or socks and really put pressure on all corners edges thin spots etc. I just walked around in circles for over an hour. Not to mention the stuff feels so good on your feet! By that point I was so relieved that it all went in I could not stop just walking in circles looking at my new cockpit. Love it! You can do it! Good Luck!

Great product but you will need to unroll and let the flooring relax its shape before trying to install it.

The backing is not sticky enough you will need outdoor marine glue for it to really hold and it will melt easily if something hot gets close to it . But it does look good. There is not much on a roll . I have a 24 foot pontoon and I had to but 6 rolls to do the whole floor where we walk.

Hate this product! Looks awful after a month of installment. The color runs. It did not stick well, had to use additional adhesive remedies. The factory cut was not straight which really sucked for installing several strips. Wayyyy too expensive for the quality of the item. Definitely would not buy again. Very disappointed.

Works so well help keep cooler cool and keep ice in the coolers! We use cooler to climb in and out of the boat! This helps so there is no more slipping off the cooler. I used this on my 2 yeti coolers! Easy to clean and material quality is amazing!