Knightsbridge SFR7000MW Screw Less 13A 1G DP Switched Socket, White

excellent devise

Hi,Already have an existing 'WITH screws' blanking plate in place and not sure if fitting this SCREWLESS PLATE is therefore simple, or not.. the part came in a labelled poly bag but no instructions. YouTube led me to try prying off the clear inner plate, but it won't detach completely. Advice appreciated. Have I bungled it already?

Looks nice without having screws on the front. You will see the edge of the plastic/metal that is behind the plate when looking from the side.Only minus is the plastic box that houses dimmer electronics (in purple), which is the full length of the back plate. I used it in an old metal housing with 4 screw positions and had to remove two screw positions to get enough space.Also, do not tighten the nut too much that holds the dimmer switch to the plate as then the button will no longer pop back out.I am using it with "Amazon Basics Professional LED GU10 Spotlight Bulb, 35W equivalent, Warm White, Dimmable - Pack of 6" ‎929001870424. By setting the minimum dimmer setting lower I can dim the these 3.2W LED lights very low.

I decided I wanted some screwless light switches and power sockets to replace the cheap ones in our house. The house is less than 10 years old so I would call it a new build/conversion. There is no old wiring and we have what I would consider nice flat white walls. I did a lot of hunting and research for switches that I thought looked the best without paying £20 or more a switch.I thought I’d hit the jackpot when I found these Knightsbridge ones as I wanted matt white screwless.Unfortunately, as Forest has described; the transparent backplate makes it look like the switch is not installed correctly and looks like it is floating off the wall.Undeterred, I thought maybe I could paint the edge of the backplate white to match the wall, unfortunately that led to me discovering another issue. If I screw the backplate enough to make it flush with the wall then the front plate does not fit snug against the backplate leaving a small gap half the way around the switch.I guess I could loosen the backplate a little so there is no small gap between the front and back plates, but then there will be a gap against the wall instead which I guess I could fill using filler and then paint. A lot of a faff when I was considering doing 25 light switches and the same again in power outlets!It’s crazy that the back-plate is not the same colour as the front-plate.It was also a pain to install the wiring due to terminals that could be larger to accomodate more wires. I needed to get 4 earth cables in this first one I installed - not easy.On balance, I think my hunt for nice light switches continues.

Love this even though it’s a standard bit of kit. I bought an American toothbrush charger, 100v over our 230v. Checked if the toothbrush would accept this etc.. and it works like a charm.Finally can use both sockets in the bathroom, need to get around to testing if both can be used at the same time.Good price point, looks good inside a vanity cabinet, 5 star for doing everything I would expect and wanted.

The actual unit works fine, but perhaps I was unlucky, but the galvanised box I bought from "Wickes" did not fit. It needed a deep box, as the unit is quite deep, so had to chase more out, not a problem. Then had to grind off both the top and bottom fixings from the box, however still would not go in, so had to grind the side fixings almost to the thread hole in order to get it to fit into the box. I fitted one of these units in the kitchen last year (not this make) and it went straight in, no problem. So it works, but be prepared for a bit of fettling.

Love these light switches look good with no screw holes to bother cleaning around.

I bought these to complement some expensive ones. These were meant to be for the places where the sockets would be less visible. They’re definitely nice enough to have completely replaced the ones I paid a horrible amount for! Nothing like the plastic white ones…much much nicer! Metal fronts add a real quality, as does the flush fit. Nice rocker switches.