Anzo USA 111113 Ford Expedition Black Clear Projector With Amber Headlight Assembly - (Sold in Pairs)

The lights arrived well packaged inside individually sealed boxes. There were no instructions included, however, there are videos on YouTube that help to explain what needs to be done. The only part that isn't just "plug and go" is splicing 4 wires into the parking lights. The green and red wires pair up to connect to a reddish/brown wire for the parking light harness. The black wires connect together to splice with the black/green wire for the parking light harness. Most videos recommend that you use a razor blade to make the splice or use a splice connector. No connectors come in the box, so prepare according. I just soldered the wires accordingly and it only took a few minutes total. Make sure you test the wires first before making your final connections. The LED lights will not turn on if they are wired backwards. You can easily test the proper connection by just slipping each bare wire into the harness connector and turning the parking lights on. I did this on each light and had one backwards first time through. Once you're done and the lights are screwed back in, be sure you check the height of the lights. They are adjustable by turning the round screw at the tip by using a Phillips screw driver. I had to adjust mine a little higher than they came in the box and they worked beautifully. Take your time when installing and you should be very happy with the finished product!

I recieved the package of the pair in a big box. I loved how they were well wrapped when I tried separating the light from the sponge it was difficult as the plastic bags were strongly attached to the sealant around the lights. No instructions came with it and from what I can see it can't be difficult to install them. Unfortunately, I didn't install them myself because I did full front renovation. The car electrician charged my around 110$ for installation. Once installed on the car, they were vey nice looking, bright and unique. Along with front bumper repaint and grill insert, it came out amazing. No problems so far and will update if I face any problem. By now 21.12.2015 I had only one problem which is the low beam died a few days ago and this car is daily driven but not too much at night, basically, going to work and back. I'd recommend replacing the stock bulbs with higher quality for longevity as you don't wanna be pulling off your newly installed HL.

These look great, make the Expedition look at least a little unique. Nice LEDs, and the halos are quite bright. The bulbs included are standard ugly yellow, can try upgrading to one of the better tinted bulbs, but in comparison to the LEDs and the halo the headlights will always be yellow. So did put in a HID H7 into the lowbeam slot (flashing the brights would make HID on the highbeam slot undesirable, as they don't activate that quick). Looks a lot better, but messing around with the units ended up with a dead inner driver side halo light, from the converter box (which is spliced to the parking light bulb wires nearby). So I unplugged the driver side inner halo so it's at least symmetric. I'm sure there's a way around the dead halo, not sure it's worth the hassle currently. Rest of the unit is working fine, though. Initial install does require splicing, I went ahead and soldered the wires to make the connection better.

Nicely done

Edit: 1*... 2.5 years later, peeling on the outside, murky projectors, flickering DRLs Old revoew: 3* Decent projectors, BUT: 1) NO instructions included for a product that needs additional wiring to function fully 2) needs to be spliced, no crimps included, no suggestion to order them either 3) bs name suggest "America", but this is a rebadged no-name Asian product.. probably identical to the 3 or so other brands that sell the exact same design. For much cheaper. "Anzo" is just a sticker affixed outside the box. Theyre not knockoffs and this is no "anzo original design", its all the same product from the same factory. 4) Atrocious halogen bulbs included, toss em and switch to HID immediately 5) uses a different type bulb than the stock headlight for the vehicle it is made for....for no apparent reason.

These really brought a contemporary style to my 2007 Expedition.

They look GREAT. All though in installation instructions you can search it on youtube on how to install. It was a very easy install.

Great fit. Exceollent light provided. (adjustment may be required). Very well packed, w/ no instructions, but OK even without. Excellent product.

They arrived very fast and am very happy with the purchase. The quality is good and other than needing a splicer for the extra lights on it, the install was very easy. They are very slick looking and the price was amazing (I have looked around everywhere).

Halos must be wired into existing lights as well as the few dotted lights. Overall a fantastic light and I reccomend it 100%

Quick easy install even though no instructions provided in box. Both the high beam and low beam bulbs provided are halogens, very dim compared to HID or LED bulbs available for vehicles today. Replaced the low beam projector bulbs with H7 LEDs. So far they look great. Will review after some time and usage!

Looks nice and gives the truck new look