Vision Miner Nano Polymer Adhesive (50ml) - Ultimate 3D Printing Bed & Build Plate Adhesion - No Mess, Non-Toxic, Works for PLA, ABS, PEI, PEEK, Nylon, PC and More. Easy Application, Easy to Clean!

Okay, this stuff sounds like a scam, right? Buy a vial, coat your print bed, magically your prints work better. Huzzah! It works. I'm not going to claim this solves all print problems, because it doesn't. But it does *seriously* help with bed adhesion problems. If you're printing something that's finicky - say, an articulated robot with its parts connected by runners - this will take "frequent failures" and turn it into "rare failures". You might be worried about price; how long does one of these last? Well, I'd judge that coating *the entire bed liberally* uses maybe 2-5% of the bottle. So you might think "ugh I'll go through it quickly" . . . but you don't have to reapply it each time. Just reapply it when the bed starts sucking again. In my experience, this tends to take months. And I'll let you do the math on how long "5% of the bottle every few months" will last. Hint: It's a long time. This is a good product. It does what it claims and for a ridiculously low per-print price. It's a tiny bit of an upfront investment but not an overwhelming one. Strongly recommended.

I’ve tried several plate adhesives, including Bambu Lab’s Liqui Glue, Magigoo, and standard glue sticks, but Vision Miner Nano Polymer is by far the best I’ve ever used. It’s extremely easy to apply and lasts a long time. I was having trouble with PETG sticking to one of my G10 build plates. After applying Nano Polymer, the PETG stuck perfectly during printing, and once the plate cooled down, the parts popped right off without any issue. Even after printing multiple parts in the same spot, adhesion remained strong. This has become my go-to adhesive anytime I run into adhesion problems. I primarily print with PLA and PETG, so I haven’t tested it with more exotic filaments, but based on my experience, I’d highly recommend it and I’d be confident it works well with other materials too. The only issue I had initially was applying too little adhesive. After watching their instructional video, I realized I wasn’t using enough. Now I follow their method: draw an “X”, circle it, and brush it in two directions. Since then, it’s worked amazingly well.

Absolutely amazing glue. I like to work with lots of different materials quite frequently. From PLA to PETG, ABS, ASA, Polycarbonate, Nylon, PPS, and several Carbon Fiber composites. I wanted a glue with strong reliable adhesion, and after looking at certain options such as magigoo, I found it a bit annoying to have to use and purchase various formulations of glue for all the different materials I use, and wished there was an "All in one" glue that just works with everything. I then discovered this stuff after watching some videos from Visionminer on YouTube and it sounded exactly like the glue I was looking for. Ordered some and let me tell you, it works with EVERYTHING I mentioned earlier and more. Super simple to apply with the included applicator brush, dries in seconds, hit print, and walk away knowing that I won't have any issues with bed adhesion. Only thing it doesn't work with is polypropylene, but that stuff has trouble sticking no matter what method of adhesion you use. Other than that, EVERY. SINGLE. FILAMENT. has worked for me with this glue and I cannot recommend it enough. The price is more than worth it for the peace of mind alone, and it will last you a good while as well since one application tends to last for several prints. 10/10

Let me tell you, the Vision Miner Nano Polymer 3D Glue has completely blown me away. I've wrestled with my fair share of adhesives over the years in this hobby, and honestly, this stuff is in a league of its own. The adhesion it provides is just phenomenal – prints stick firmly to the bed without any annoying warping or lifting, even with tricky materials. But it's not just about the stick; the release is equally impressive. Once the bed cools, parts practically detach themselves, leaving a clean surface behind. No more scraping and potentially damaging prints! The application is smooth and even, and a little goes a long way, which means this bottle is going to last. Honestly, the reliability and ease of use this glue provides have made my 3D printing experience so much more enjoyable and stress-free. Consider me a convert. From this point forward, Vision Miner Nano Polymer 3D Glue is the only adhesive I'll be reaching for. It's simply the best I've ever used.

First, the good stuff. It works. Prints stick to the bed, and then get unstuck relatively easily after cooling down. For the most part. I have had a few occasions where scraping was necessary but that’s to be expected with some materials. The bad: mainly that applying the product is extremely awkward. The way they tell you to do is by drawing a cross and a circle covering the print area, then using the included brush to spread it. The “brush” is a tiny one, with half a dozen stiff nylon bristles. The adhesive is very liquid. The brush barely spreads it over a centimetre - it has no chance to spread it over the bed. After a lot of frustration and asking other users in online communities, I settled for diluting the NPA with 1:1 isopropanol in a spray bottle. 2 whiffs of that over the bed, then spread with a microfibre cloth. That works well and lasts many prints!

I'm shocked that it works as well as it does. The advertising, surprisingly, wasn't full of exaggerated nonsense. This is the perfect bed adhesive for even filaments that seem to hate existing. The best part? It's somehow also water-washable. It just comes right off the build plate under the faucet. Unbelievable. Well-earned 5 stars for this stuff.

This stuff is like bed adhesion god mode. Its too sticky, it has lifted the pei off every plate I've used it on, and i've diluted it with ipa, tried removing hot and cold.... its just crazy how stuck prints are with this stuff. I dont really mind as most of the PEI i used it on was pretty well worn out, and for a few drops of this to rejuvinate it to the point of being too good, even when i've diluted it down 3:1 is impressive. Will definitely buy more when I run out in like 10 years.

A must-have for printing ASA. No more brims! I should have bought it ages ago, and I will keep buying more!

Best glue ever, strong alcohool smell after application and bed heat up but holds really good. So for just added more and more after prints without any issue, printing nylon on textured pei!