[Upgraded 2025] ICBEAMER 37.8" 980mm Sunroof Wind Deflector,Universal Fit Tinted Moonroof Visor for Deflecting Noise, Rain and Windy Weather, Car Accessories Sun Shade Dark Smoke Smooth/Waterproof

The top of your vehicle is contoured so best to do these in the heat. follow the instructions after you get it centered and exactly where you want it. take a maker and mark where the back ends on each side go, make sure both ends are attached firmly where you want them. then do corners to center. press down and a bit back on bend. Look to makes sure your tape is touching. the straightness of the shield will bow up in middle so viewing the actual adhesive tape contact, continue pressing till it has no gaps.. I then sat my vehicle in direct sunlight to help the shield to adhere to the contour of my vehicle. an hour later i took for spin in 20mph winds and it held nicely..... if you clean the surface with windex, IT WILL STICK.

I was hesitant to buy this as it was adhesion only. All of my other cars used OEM deflectors using secure clip mounting. I prepped surface with rubbing alcohol to clean thoroughly. I warmed both tape and roof of car with a heat gun to promote better adhesion. Adhered to vehicle and left it inside a heated garage at 74 deg F. Did not drive car for 4 days. Took it out and hit the highway at 58 mph. It blew off the roof of the car, and hit the vehicle behind me. Luckily no collision occurred. The unit is advertised as using "3M waterproof tape". Wrong, It has a tape similar to 3M. It is a poor quality tape. See my attached photos. One is an extra roll of tape supplied with the unit. The other clearly a proper 3M tape. Note that the 3M tape used their logo on the backing liner. The unit supplied tape does not. Frankly, I find this disturbing. Using the 3M name when the tape is not. 3M "type" is what it should read. So to summarize. beware when purchasing this unit. Purchase some real 3M tape to replace the one on it. Also, the tape applied does NOT allow for any water to run off trapped under the deflector. It should have proper channels cut into the plastic to allow run off. OEM units do. On the plus side, it is a nice looking unit for the price. Too bad the quality is lacking in manufacturing.

Good

Fit, style and quality of the visor was very good. I only gave 4 star rating because the double sided tape is lacking in quality. I done a good prep job and let the visor "cure" in 75* sun for a few hours. I did not drive it until the next day and it blew off 15 miles into my trip. Luckily I pick it up off the highway before another vehicle ran over it. I purchased good quality Gorilla double sided tape and done the same prep and same cure in the sun process and so for 3 weeks later its holding on rock solid.

It was very easy to install did it myself

Installed mine on a 2012 Hyundai Veracruz. Makes a nice difference when opening the sunroof. Less noise and air buffeting. Had it for about three months and it's still stuck on. So far, so good. Update April 2025: Have had this deflector for 15 months. It's still on the car however it has warped significantly. Still does the job of deflecting air but looks pretty bad on the car. Planning on replacing it with something else.

Nice ceramic iron.

It DOES NOT fit my 2007 Toyota Sequoia! "amazonconfirmedfit" says that it fits my 2007 Toyota Sequoia. It Does Not fit. I purchased this deflector over a year ago and I'm just now installing it. So, no return for me! The width and depth are sufficient, but the contour is not! the 2007 Sequoia roof at the sunroof has a convex surface... it is not flat and this wind deflector mounting surface is not convex... it is flat! This deflector is pretty stiff, which would be OK if it had the proper contour, but it does not and so the flex required to match the roofs contour is too much for the self adhesive tape to hold it in place. I placed a 25 pound dumbbell weight on it overnight and the stiffness still pops it up again. Cannot chance going through the car wash with this thing! I'm taking it off. The quality of the deflector material is great, the shape (contour)... not so much! Got to try to find one like the one I originally installed in 2007! Haven't had any luck yet. The original was broken with the part number stamp missing. Unfortunate for me!