UPGRADED AGM75510755 Kenmore & LG Dryer Parts 4581EL2002C lg dryer rollers 4561EL3002A AGM75510755 Dryer Idler Pulley 4400EL2001A Belt Spring, Compatible with DLE2101W DLE2301W DLE3777W-BY AMI PARTS

Good kit, quality parts. No more squeaky dryer, but 1 or more of the rollers is not perfectly round or smooth. Dryer has a small thump noise from roller not being true. Hopefully it will work itself out, probably won't though. Can't beat the price for this kit, OEM replacement parts of what's in this kit are over $100.00.UPDATE - Ran about 6 loads of laundry, good size loads of jeans and towels. Ran them for an hour each on high heat and now you can hardly hear any noise from the rollers. The 6 loads were run back to back, so the drum was always warm during the 6 hour time. I don't know if that makes a difference, or just helped speed up time to true the rollers out. Just a heads up, if you install this kit and have a roller or 2 that are not completely true, the thumping noise is going to be louder when you test the dryer after you are done when there is no laundry in it versus with a load of laundry in it.Update:After about 7 months dryer rollers are squealing again, I don't think that these are really that bad of an item, I think that they probably needed more grease on them. I do remember when installing them that they did seem like they were skimpy on grease but left them the way they were. I haven't taken dryer apart yet to fix them, so I can't say whether greasing them will work or if they have done major wear to the rollers requiring replacement again, but I will update this again after I take a look at them and see. I will regrease them with automotive wheel bearing grease since theses rollers do see a lot of heat, original grease might not have been designed for the heat that is created from dryer.Update: After taking dryer apart again to see if rollers just needed grease or not. Rollers were completely dry, not a trace of original grease left on them, they were completely dry. Bolts and roller bushings had wear on them and will need to be replaced again. Bolts and bushing just have a thin polish coating on them, once that wears off they eat into each other pretty easy. Bolts need to be harder steel to keep roller smooth finish on them and bushings the same or they should be made out of brass like most bushings are since brass acts like a dry lubricant. Regreased rollers with wheel bearing grease and right now there is no noise, hopefully it will last long enough until I get new ones installed before the parts that have the wear start start cutting into each other again.

Perfect fit and a money saver.

This kit worked great for a few months, then two different loud noises started and got progressively worse. I had to replace these rollers with a higher quality replacement. When doing the replacement, one of these rollers was shredded and one was rusty. Bearings seem to be very low quality. I'd recommend buying a different version. The belt and tensioner seem fine, problem was with the roller bearings.

The media could not be loaded. We have two LG dryers in our house and I've rebuilt them both in the past year. I ordered a cheaper roller kit off of Amazon and it only lasted 10 months. The kit only bushings and not actual bearings, after 10 months the axles wore flats on them from the friction of the turning bushings and became very difficult to spin under load.I ordered this kit as a replacement for the replacement and was very pleased to discover that the rollers have actual ISO stamped bearings in them. On the flip side the tensioner arm pulley included is a stamped from thinner sheet metal than the first crappy kit but it seems to work just fine. These rollers really spin easily and are much quieter than the first kit which only had bushings and not bearings.Replacing these isn't that difficult, although it takes some contortions to remove the rear axle posts for the rollers if you don't take the rear plate off the dryer. I could probably do this job in about 30 minutes now that I've done it THREE times. ;-)

These were great and worked perfectly. Could not be happier with this item

My Kenmore Elite dryer started to make noise. My husband took it apart to find the spin wheel dented due to not being able to spin because of hair getting stuck on it. We ordered this set and only replaced the drum spin wheel. And no more loud noises when using our dryer :) I recommend this set. The parts seem durable and it was easy to install if you are willing to learn from YouTube :)

UPDATE - 09/14/24**** SELLER SAW THIS REVIEW AND PROVIDED A FULL REFUND. THANK YOU AMI PARTS. *****I’ve purchased this from Amazon in the past and it was acceptable in performance in my older dryer. I bought this for our newer dryer when its original rollers began to squeak. After installing this set the dryer had a rough sound with a wobble which soon turned into a wobble with a squeal. It was past the 30 days return period and I’m waiting to replace these when they fail.

I opened up my dryer and took a picture of the number on one of the existing wheels. These matched. Installation was easy, there are plenty of videos online. It did help to have a second set of hands when reinstalling the drum.I liked that this had everything I needed in one kit to do a complete refresh of my dryer. Oh, and way less than a new dryer.