Frigidaire 5303051519 Genuine OEM Bake Element for Ranges

Very easy to install. UNPLUG THE RANGE/STOVE BEFORE YOU DO ANYTHING!!! You basically unscrew a couple of screws on each side and gently pull the old heating element out. Before you pull the wires apart off the old element BE CAREFUL and HOLD ON TO the old wires or they WILL kind of get sucked back into the back of the range and behind the insulation. If that happens you have to unscrew the back panel off the entire back of the stove, grab the wire, fish the wire back into the hole so it goes back inside the oven and grab it before it gets sucked back in. How do I know this? Take a guess. Taking the back panel off the stove is easy it just takes more time to take off and push the wire back in then put the back panel back on

I’ve wait a while to post my review to make sure it continues to work. Got here pretty quickly and wasn’t as hard as I thought it was going to be to install, did have to take the back panel off my stove in Order to make sure it was installed correctly, also has to be the ends straight as they where in an L shape, but overall only took me about 30 minutes to install and it works great and is still working almost two months later.

So far, the element works great. Perfect fit and installation is very easy.

Oven got hot

Super easy to install! Saved me hundreds of dollars because I was about to replace my entire stove. Even though the listing says Frigidaire, I have a Kenmore and it worked just fine. All I did was match the picture with the one I was replacing because my model number wasn’t listed.

I would give 4.5 stars if I could. The part was delivered quickly and was the right part, except note below. It was quite easy to install, just be careful because the clips from the oven wiring to the element can fall behind the back wall of the oven once disconnected from the old element if you aren't careful, and would be difficult to retrieve; and the replacement element had connectors bent at a right angle to the element which should be no big deal but once the wires were connected it was a bit of a struggle to get the connectors back through the rather small openings in the back of the oven. The old element had straight connectors, which fit through easily. I was hesitant to bend the connectors. I might be a little afraid of the wires popping off trying to pull them back through the holes again because of the tight fit, should I ever have to replace the element again. Not sure how I can rate longevity of the replacement element. It's lasted a week so far!

I have a Frigidaire oven from the early 80s model # REG-43. I couldn't find a replacement bake element for it anywhere and even frigidaire customer service said they don't have any parts that support a product that old. I saw this on amazon and it looked to be the same shape, so I thought for $22 I would give it a try and see if it would fit. It does and it works perfectly, exact same size and the connectors are the same size and orientation too. This will also fit the REG-74 double wall oven too.So glad I decided to give this a try and managed to get my oven working for $22 instead of buying a new oven.

I ordered this element after ours burnt out and began sparking. Very common occurrence according to Google. Wasn't sure how to compare part models so ordered this based off the fact that it looked like the dysfunctional part currently in our oven. Once it arrived we compared to the old part and it was identical so my husband and I watched a quick YouTube video and set to work. We didn't turn off the power to the oven but were very careful to not allow the wires to fall back behind the oven panel. The one caveat mentioned in the title was the silver, perpendicular pieces at the end of the element that stick up. Our old part had them laying flat. I'm not sure if these were supposed to be bent flat before installation but it quickly became obvious that they weren't going to fit through the slits in the back of the oven without bending them. Fortunately our little adjustment didn't create any issues and the newly installed element works perfectly.

Fast delivery, easy to install, cheap but delivery fees were high. First, when I installed it, It didn't work ( actually my entire stove was not working. The lights on the stove were on but no heat), but later it turned out that the stove breaker in the garage was down. I turned the breaker on and the stove worked fine.

Installs in minutes and is a direct fit. Just be sure to order the correct one for your model oven.

My element arrived before the estimated time. Oven is working great again.

I am in Canada and it was the exact same element. It was really easy to fix and insert. Works better than before

Just in time for thanksgiving. the element of my cooker broke down few days before the thanksgiving.I ordered this product. Came before thanksgiving. And it works very well, easy to install.