Automotive - Metallic Gray - 1 Gallon - Rust Inhibitor & Protective Coating for Cars, Trucks, & Metal Surfaces, UV Resistant, No Topcoat Needed

Five star review. This rust inhibitor paint is the best stuff one can buy on the market and even the army and navy and major architecture landmarks use it and has genuine patent awards. Does that tell you something? It will save your precious automotive vehicles or any metal items from rusting or worsening condition. There's a lot to study about the right application and best results for this paint but I'll break it down. The photos show my cars undercarriage so in my case it is an automotive project. Use a conjunction of products from rust bullet for best results, metal blast, the paint, and clear coat. You also require disposable brushes from the dollar store, nitrile gloves, mask, overalls, goggles, PPE. Bloxygen too if your going to reseal the paint can. 1. Clean the undercarriage of the car, prep work, use a garden hose and wire brush to scrape off oil and dirt etc. Remove loose rust. Step 2, when totally dry you'll jack the car up and spray metal blast dissolving the rust and creating an adhesion to the metal so when you paint it'll stick. It undergoes a chemical reaction. Let sit for 20 min or so, then rinse with garden hose and dry. Step 3, paint in a garage indoors is a must with temp 50-80 F and no rain, 1st paint coat by brush and 4-6 H dry time, important, don't wait more than 12 H after 1st coat, it'll harden so do 2nd coat after it's dry. Filler, then sealer. Do 2nd coat, let dry, boom, ready for two clear coats next, 2-4 H dry time and when every nook and cranny is covered just wait 72 H or less, full cure time before exposure to outdoors. It'll make the metal look brand new and shiny with the clear gloss. You won't see any rust underneath. It's not that expensive and should be used way more often in a automotive world of mistreatment and any vehicle with this conjunction of paint will last forever. The paint acts as a filler, stopping the rust, it's water resistantance is unbelievable, I got a good amount of paint on my hands and the water evaporates within seconds and the stickiness is the bond to the metal so it's staying there in form so long as the car body is there too. Superior barrier on the metal, recommended to do the undercarriage first and then take car panels off, (fenders, bumpers,) and paint the wheel well areas and inner frames especially. You can do the trunk and bench seat areas too if your really into it but especially undercarriage area for winter driving. Ventilated area is a must, strong odor and causes bad headaches so be professional when using it. It's not ordinary paint, drys like cement so cover floor with plastic sheets. Note- only pour out what your going to use in an hour and reseal the can immediately. Moisture sensitive. Opened can will last a month with bloxygen. Stir before use. Depending on how much rust you have or area the small 1/4 pint cans will barely cover half your undercarriage 1st coat, 1/4 PT = 6 SQ FT. A quart is plenty for 2 coats with a little extra and a pint would be enough for 1 coat. My project turned out phenomenal and saved my show car that I put so much time and effort into and yours can too with this wonderful paint product. If you want the best and are willing to put time and effort into it this paint is top of the line. Not a cheap wd40 job that lasts a season but lasts a lifetime. Highly recommended, five star review.

This is a silver coating very similar to another popular product at a fraction of the cost...With multiple coats you can fill some pretty large pinholes.

To all the criers on here and elsewhere about the product drying up in the can. I have a partial can after 9 months and it's still not dried up. You have to keep the surface clean where the lid goes back on...duh? LOL. Anywhoozal, this stuff seems pretty tough. I used it under a rusted mower deck, because inept people believe they can mow wet grass and not clean under the deck when done. Then wonder why it rust... I digress. Love this stuff, but it is expensive, hence the 4 star rating for the small amount of product received.

I used this on the hood of my 1972 VW super beetle and I'm about to apply it on the deck lid and roof. I used locktight rust remover gel on the small amount of rust spots, followed by a mild degreaser to wash, then applied rust bullet. It brushed on smooth, left no brush marks, covered beautifully and actually looks nice. I'm confident that this product will protect the metal while also creating a nice smooth even surface to paint over. I've had it on my hood for over a month now and its holding up well. The can is bit of a pain to open but, I'm 60yrs old with arthritis in my hands and I managed to get it off without spilling any so.....regardless of the 5 mins it took to pry it off, once I saw the performance of this product? I'd gnaw it off with my teeth if I had too (almost) to get it open the product is worth it. Don't shake the can, leave it upright, pry open and stir it well to insure you get no bubbles, and brush it on your classic vehicle with confidence. I just ordered more p!us a can of rust bullet whiteshell and a can of their blackshell which I plan on using inside and outside of my vehicle. You won't find a better product, don't let the difficult can scare u off this great product. Remember, if it gets bubbles while opening, let them dissipate before application, stir until mixed well with no bubbles for a perfect finish. Enjoy, and good luck with ur restoration project.

I sprayed this in my hood and trunk area and brushed it on my wheel wells on my 1969 Beetle. Everywhere but the area in the picture got a coat of Rust Bullet blackshell coating. I also coated the underside of the floor pan with both. It is thin to brush on but coats well. It is easy to spray with a HVLP gun but make sure you clean up quickly as this stuff turns into a plastic type coating before you know it. Thin coats are better than thick ones. I would suggest 3 thin spray coats rather than the 2 coats they call for. 2 coats may be ok if you brush or roll it on. If you use a brush or roller be prepared to throw it away after using it. Some tips for using this: be careful opening the lid as you won't want to bend it for storage reasons. If you spill product on the lid sealing surface, clean it off! Use a cotton swab and thinner if necessary to keep area clean to allow the lid to reseal. This product is instantly activated when you open the can, so don't expect to store it forever after it has been opened. I have made it last 2 years somehow by resealing it carefully but I wouldn't count on that every time. Overall, I will continue to use this. It works great every time and encapsulates the rust.