PASYOU Adjustable Squat Rack Heavy Duty Gym Rack Stand Multi-Function Weight Rack Stand Push up Portable Strength Training Dumbbell Rack power rack

The rack is great quality! I bought several on my gym journey, but this is the only one I have kept. Both the upper and lower support bars are very stable with little to no wobble. Other cheaper racks I have used also feel like they could tip, but this is not something I experienced with this rack. That being said, I have supported it with a 10kg weight on each storage post. Putting it together was so simple with only 2 bolt sizes and 2 washer sizes. The included spanners were good enough quality, but I made sure to tighten everything with a socket wrench. Size wise it is perfect. I use a 155cm barbell, which fits nicely. I find there is enough room to get a bench between the posts without it taking up too much space in the room. There is no doubt that you could spend more and get something even higher quality, but for a home gym and a barbell with around 80-100kg, I think this is more than enough.

I read the reviews on this some have valid points. Let’s get the negative bits out of way. I marked it down a star not due to one thing but a few minor bits, it came well packaged but it a a tiny crease (probably for manufacturing)& a few tiny paint imperfections.One of the safety bars is also difficult to fit in and the screw heads scratch the frame, so I taped the offenders with electrical tape.I totally get what the other reviewer said about the width of the rack stopping you doing wide grip bench press. The only solution would be to make it adjustable which would affect the solidity of the rack, wider would make it tight to stops on your bar, which could cause other problems . The point about it flexing in another review is because it’s not tied off side to side ( it’s a rack not a cage but I haven’t found this a problem. Good stuff, it goes together easily & a decent spanner is supplied although I used this with my own ratchet spanner for speed.Well packed for delivery including steel packers to protect the cross member lots of bubble rap.With the bigger cross section the whole thing feels solid & other than the minor issues is well made. It’s the perfect height for me but I’m not very tall, if you are 5’9” plus you might find that an issue for squats. Nice and stable when placing the bar back after squatting . The j hooks look good & solid with good looking welds but time will tell on that . I like the weight plate storage but no good for anything over 10kg size if sited flush to a wall.Pleased overall hence 4 stars

Amazing quality for what it is - easy to put together took me an hour and a half on my own. Really great quality safeties. The j-pegs may not be as trustworthy with heavier lifts as not much of a lip and the plate storage isn’t much use (would be better on the back of the back posts instead) unless smaller plates but a nice touch still very impressed for the price. Seems very sturdy but then I’m not planning on doing my heaviest weights on it so not sure if you’re planning on maxing out lifts on it but for regular workout weights it seems very sturdy

Very well packaged, High quality parts, easy to assemble via instructions. I was very pleased with the look of the rack, and and the stability, and more so the safety features, as it will be used by young members of my family. A quality product, well thought out, extremely well priced. I will be looking for further buy's from this company.

I am impressed with this piece of kit… seems well built and solid. Instructions were easy to follow all tools needed are supplied.

As the header saids, you get what the picture shows you, all the measurements they provide are correct to the product. After using it for a month essentially everyday I can say that the frame itself is solid, and well over engineered to ensure that it can handle heavy weights so not too much to complain about, however I do have a few issues that are lacking in the overall design. What I have found is that when setting up for a weight that is over 80kg's on the top setting, the rack will tend to want to tip over when unracking/racking unless you put weights on the base (the slots on the back), as the base itself is hollow (doesn't appear to have any additional thickness compared to the rest of the rack) which is fine as simply putting on lets say 20kg's per 100kg's on the rack offsets this, except when I need to use all my weight to workout. I've managed to deal with this by putting bags of builder sand on the back. Another issue I have ran into is with the j hooks and safety spotters. The j hooks themselves are able to hold the weight as intended, however what I've ran into is that they are very narrow couple that with being tall and I've found reracking the weight after squatting/overhead pressing to be a bit perilous especially when there isn't a safety bracket above the highest pin option, I've managed to deal with this (sort of) by putting the j hook on the second highest option which isn't optimal, I've also ran into this issue while benching and using the smaller positions where there isn't a safety bracket I've instead had to set the safety spotters to the highestposition and drop the weight on them instead of going for a rerack, which feels very sketch. In my mind a simple fix for this would be to just have a piece of metal that slots into the tube and either sits on the j hook inside or 'clips' into place. Then the safety spotters do what they should do, they catch the weight and are well built, again an issue I've ran into is that when setting onto the higher options (positions 8+) for overhead pressing I have had to drop the weight onto them, it wasn't anything much only 50kg's, with one side already in the j hook and dropping it a distance of a couple inches (few cm's) and it had managed to bend the bracing which I found odd, since you'd think the pin and the bracket facing towards me would have taken the force, but aparently not. I wasn't asking anything much off of the safety bumper, only wanted it to catch essentially 25kg (since the otherside was already racked) from a small height, I know it probably wasn't intended to be used outside of the 1-7 positions, but I'm not asking it to catch 100kg's from a a metre in the air. Again another straight forward fix either ensuring the back bracket isn't taking the entire brunt of the force when outside of the 1-7 positions, or even adding smaller safety bumpers meant to go above the 8+ positions. Then last little annoyance, this one is genuinely not that big of an issue but the locked rubber isn't rubber, it's a plastic/resin mix that gets damaged easily when using any amount of serious wieght, however this doesn't bother me as it is essentially aesthatic, just a little dissapointed it isn't actually rubber/silicon. Also I would recommend getting a decent wrench/power tool to put the nuts and caps on as what they provide will leave you swearing, bruised and bleeding. Overall I'd still buy it and use it as it fits the purpose I needed it over a full rack (cheaper by a long shot, easily movable and easy to store in a tarp) and the issues I'm facing with it are mostly due to my height, still would like to see an adiditon of safety bumpers where the plastic clips are as they already send two pieces of scrap metal extra with the rack, I would just hope they'd trade those out for something useable.

Great product now need to buy more bars and weights great for project home gym 🤣

While this product does have fairly good build quality it is nowhere near big enough for using as a squat rack. I am 6’2 and my shoulders towers above the highest point making it unsafe for re racking. The distance between the front and bar for the safety bar are also far too short to use effectively. This product would be suitable for a child, not a grown man regardless of the weight it holds.

The parts are of solid quality and easy to assemble. Perfect for squatting, for bench pressing one needs to adjust the width to the max, it works for my size but if you have really wide chest and shoulders then it could be an issue (this has been mentioned in other reviews too). What I liked the best is the customer support. My package came without one part. I contacted the customer service and they sent the part to me right away, together with extra tools. They were very friendly, customer-oriented and supportive throughout. I got the missing part in just a couple of days. Overall, very happy with the experience, exemplary work of customer support! You can be sure that if you have a problem with the rack they will be there for you to fix it.

Quality is good. Assembly was a little difficult but my boyfriend and I put it together. The value is good. It fits well in our basement with a full Olympic bar bell. I like that it’s adjustable of where you can place the bar.

El producto está genial solo me faltó un tornillo, pero por todo lo demás genial.

It was simple to assemble. The instructions were really well made. I assembled this with my wife and it took 30 mins. The materials are really sturdy and really high quality for the price. Really happy with the purchase.