2 Pcs Lift Top Coffee Table Hinges,Gas Hydraulic Mechanism | Hinge brackets only,screws not included,for lift top coffee tables,folding desks,storage tops and bench tops

I was nervous to buy because of other reviews but I’m so glad I took a chance on this. It was easy to install, works great, and really personalized my furniture to my needs. The cons- no screws but I had some on hand that worked just fine. Also no directions but wasn’t a huge issue with some critical thinking. Last- not really a con to me but another review mentioned some scratches in the powder coating, which mine had as well, but personally I don’t care at all. Tips for installing- Leave the zip ties on until you have screws in both the top and sides if possible. There is a small round stopper that’s the size of an aspirin that protrudes- this goes in the top corner and should be facing the direction you want the top to pull out. I aligned it on the sides and had someone hold a book on top to make sure it was flush while I added screws and repeated on the other side. Then you can perfectly align the top in the closed position and screw it in. After both of those steps I cut the zip ties and continued adding the extra screws. The top sits exactly where I want it to and isn’t wonky like some other reviews. If this is a custom build I’d recommend waiting to add all four sides to the base until after assembly. Great value for the money, don’t be discouraged by some of these reviews. I’m not particularly handy/certainly not even an amateur carpenter but it came out great.

I completely refinished our old coffee table and cut the top off and added these. They worked great on the project. I was concerned that the heavy top (30 lbs or so) would be an issue, but it lifts smoothly with minimal effort and even my wife and raise or lower it alone. Height is perfect to eat or use the laptop from our living room couch. I noted there were much more expensive models but I couldn't see a lot of difference in the specs for the price so thought I give this set a try. I'm glad I did. They are well made and do what I expected them to. Recommend,

Good quality and sturdy. Gave it 4 stars because it came WITH NO hardware (nuts, bolts, screws) and NO instructions! I was able to figure the process out (and yes it has to be installed in a specific sequence) and have it all set. Am happy with the quality and functionality.

I bought these lift‑up hinges to build a custom drawer and storage system in the back of my 4Runner, and they worked out even better than expected. The metal feels solid and heavy‑duty, definitely strong enough to support a platform or drawer top while still lifting smoothly. Installation was straightforward, and the hinges operate with a nice, controlled motion — no sticking or wobbling. They make it incredibly convenient to access gear underneath without having to pull the whole drawer out. Great for overlanding setups or anyone who needs organized, easy‑access storage in their SUV. For the price, these are a great value and a smart upgrade for any DIY cargo system. Highly recommended for 4Runner builds or other vehicle drawer projects.

I used these for a cocktail ottoman I built with storage for my electronics. I was almost done, when I realized standard hinges wouldn’t work. These did the trick, they are very strong. This was a great value compared to everything else I looked at

Using these hinges, I built a 36x18 lift-top coffee table. The top is fairly heavy, being built from veneer covered 3/4" MDF with a hardwood border. As others have mentioned, it's a little wobbly when lifting, but this can be reduced by grabbing both ends of the table top while lifting. When in the open and closed positions, there's no wobble. Screws are not included, nor are there any installation instructions, but installation is fairly simple. You will most likely need to have access to the bottom of the table cabinet in order to install these hinges. I found it easiest to lay the top down on the floor, upside down and position the table cabinet in the desired position over the top, then mark the screw holes for both the table top and the cabinet at the same time. In this way, the top is positioned perfectly in the closed position. When ope, the table top is raised about 6" higher, and about 11" forward of the closed position.

Used these hinges to build a flip top coffee table and they worked great! They were easy to attach to the table, very stable & strong at a great price. Purchased two sets for a future project.

I bought these to replace spring-loaded ones that came with my coffee table. They work much better and are smoother than springs. The issues are with the placement and size of the holes. The holes on the arms where I should be able to put brackets for a stabilizing bar are too high so when installed, the hydraulic canister hit it so it won’t close fully. I ended up using the lower holes but that means the bar end up hitting stuff inside the table so I have to keep that area clear of anything high. The holes to attach the table are also not lined up and they’re small. I expected them to be bigger to give room to adjust bolts but they were in weird places and it was very difficult to install the screws because the hydraulic canister is in the way of any screwdriver or drill. The screw in the middle goes in sideways and I guess you could skip that one and just use the other four but even those are a tight squeeze.

Producto de buena calidad

Better than expected. You will need to do a bit of trial and error to figure out where to mount them in your cabinet based on the dimensions of the cabinet. I’m really pleased with the product

Lo utilice para realizar un proyecto de mesa de centro y quedó súper bien. Hay que nivelar antes de colocar. Súper practico.

Funciona bien el único detalle por el cual no le doy 5 estrellas es porque no incluyen pijas ni instructivo de instalación, pero en el bendito YouTube encontré un tutorial que me fue muy útil.

Muy bien viene sin herraje pero con unas 20 pijas funciona bien