BLAUPUNKT1500W 4-Channel, Full-Range Amplifier

This Blaupunkt amp has wattage ratings far beyond it's actual output capabilities. Most amplifier Dyno videos document this.How much amplifier do you actually need and whatever you buy, it has to fit within your budget.This amplifier has build quality above and beyond Pyle and pyramid build quality and is pretty clean free of alternator whine and ground loop issues. It has most features anyone needs and is designed to be a high/full range amplifier. I don't think it would do subwoofers very well, but that's what mono block amplifiers are for. If your on a tight budget and want a quality amplifier for full range sound and don't require sound levels that will make your ears bleed, then this isn't nearly as bad of a deal as the amplifier Dyno guys say it is. No you can't connect welding leads to the speaker terminals and weld with it. But for the price point it does pretty well, depending on ones expectations. If your operating on a pyramid cash flow and need a good 4 channel amplifier for full range sound. Then step up to this and get a much cleaner and clear sound (not wide open volume), LoL.It will give you better than double the power obtainable from a quality 4 channel high powered head unit cleanly.I wish amplifier manufacturer's would rate wattage ratings more inline with the products capabilities, but this is an age old problem for decades, so don't be surprised when an amp won't come remotely close to it's wattage ratings. I guess if they rated it correctly no one would buy it in hope for a super product for very little money. Too good to be true; it usually isn't.In this case the amp isn't cheap shoddy build quality. Yes they could have added higher value capacitors, but it has enough to be clean sounding. The amplifier manufacturer's are not going to build a super superior product for all but nothing as they have to operate on price point as well.To me ask yourself how much amp and what you want to do with it to determine if this product is for you and within a given budget. If you want to power subs, then mono block amplifiers are the way to go.Hopefully I have cleared the air of controversy concerning this product. I'm happy with it and the price point as well.73 Earnest K5EWM 👍. It's a keeper.

The media could not be loaded. very clean audio, super impressed. runs hot so don't over do it. Had to find a longer compression screw to get it to fit my 4GA power wiring. Totally worth the effort. can't beat it for the value.prolly got 24 hours of runtime so far zero issues or concerns. had to replace an old kicker zx650.4 and I'm glad i did. the audio is so clean and crispy on this amp.running it HPF with 4 old infinity something or others and a very old sony home theater speaker i've had since i was a wee lad.

Liked the sound output and quality so much, just ordered another sub and a Blaupunkt 2-channel amp for the subs. I add external cooling fans, they probably should consider having fans built-in. One is under my seat and would overheat under heavy load. No issues since fans installed.

Fixed my problem by getting this amp. My speakers were clipping and not enough power from my last amp. And this one powers them really good. So far so good

I do not understand the negative reviews for this product - i have been running this amp since July of 2023, it is not Jan of 2025 - NOT A SINGLE ISSUE - daily driver avg 2.5 - 3HR in IL where temps swing from negatives in winter and +90 in summer - amp on all times, at 75% crank up to all channels - not running the HPF/LPF, adjusted at the head unit - not a single issue. The only logical deduction is that people that torch these out or fry-pop them installed them incorrectly or are completely electrically-challenged. If you know how to hook-up, set, run car amps - get this one! the price is too crazy low to pass this up and you will not regret it. to all the fry-cooks out there, get something more expensive that comes with a more juice than you need and has multi-safety features that will prevent burn outs. keep in mind your amp is pulling from your car power, you do not want to experience ANY kind of electrical issues with any amp as it can compound into a major car-electrical issue down the road, and to that point, frying out your car-electric-system on a $100 amp, is just silly.

price point was great. received unit in new box. came with manual and easy instruction. Installed easy and replaced my old kenwood amp. sounds good but only lasted a couple of days and started cycling on and off. checked all connections and everything was good. seems to be overheating, because it only seems to work when it's below freezing outside. when temperature goes above freezing or during the day it won't stay on. called customer service and because it happen before the 90 days they are going to replace it, but after 90 days you're SOL. not only that, but Ematic is making me pay to ship it back to california and now it's cost me more that I expected to pay. you think they would stand behind there products and if it's defective they would pay to send it back and send me a replacement. not cool, buyer beware..... they claim it will take 6-8 weeks to ship the replacement once the defective one is received. This company sucks! I will never buy from them again. I wish i could just get my money back. Hug!Nine weeks have now gone by and still no replacement. Customer service is terrible. No seems to care and just keep getting the runaround. I guess I should kiss my money goodbye

Really great amp for the price. It is pushing two 12’s and it sounds great

Not even close to the 1500 watt as advertised more like 400w that isn’t really the issue still plenty of power for most speakers to sound good, the problem is the RCA input and output terminals are very cheap and Will fail at the solder connection on internal pcb ( just from the weight of plugging in three sets of RCA cable's ) mine started cutting out and distorting . After I traced the problem to RCA terminals and what was going on I removed the Amplifier and opened it up and repaired the loose connections by re-soldering each of the 6 terminals. After repair the problem was resolved and it’s been fine