Shadow Foam Medium Sheet – Foam for Tool Box Organisation – 1000mm x 500mm - DIY Cut & Peel Foam Sheet for Tool Boxes & Tool Storage Systems – Drawer Organiser – Red (50mm Depth)

chose this teal 5cm depth x 1metre shadow foam to tidy up the sewing tools, normally the tool need sinks to bottom of box, that takes time to locate. decided to buy a large sheet for other projects later, have over half left after this box was completed. wanted a colour that would highlight the tools, teal green seemed to match needs, decided to use green side up for low light situations. getting the layout that would work took me days, some tools are layered or on side, wearing goggles using a snap bladed knife, cutting was easy thankfully. however my hands must of been warm from fear of sharp blade usage, because fingers had little green marks, so wore gloves after that discovery. due to the lid being triangular, we made templates first out of breakfast cereal box then used 24" quilting rule to slice rectangles out of sheet of tool box size before curving corners. laid out all tools to ensure would fit then used the snap blade longer hence safety goggles traced round the boxes first, removal of material was as expected slow and steady to get a good base. cut in 3 x scissors rotary cutter and blades box underneath the cutter. the lid storage contains 5 rulers, pencil, seam ripper and snips. its not glued in yet stays against smooth painted metal. the advantage to shadow foam is when knock the metal tool box off table with lid closed accidently there is no crash bang wallop, the tools stay in place. when using, tools are found easily and extracted without getting green fingers. never blunted the snap blade or needed to snap for a sharper blade its like cutting a good light yet fruity fruit cake. all in all pleased done this.

Really good quality and for the men who love a sticker you get a sheet of em in there

Decent shadow foam and very easy to cut down to size and around tools. I would highly recommend ordering a scalpel off Amazon to do all your tool cutouts. All the tools fit snug and don’t jump out of their position. Not the most dense shadow foam available on the market so maybe not the best choice if you are really trying to cram in a lot of tools (I only noticed this when fitting my spanners in). Overall though great shadow foam for the money!

Used this to renew my archery kit, really good and very pleasing on the eyes. Quite a strain to remove the layers but taking time gets the job done. Cutting with a thinish scalpel is key. It's a good solid foam so should protect items well and snuggly.

This is a great product. I needed a way of organising the jaws for my woodturning lathe chucks and thought that a Shadow Foam layout drawer would fit the bill. After cutting to size to fit my drawer, I tried a test hole on an offcut and found that the best way to trim the bottom flush was to use a sawtooth blade on my Dremel. - NB after a couple of near misses, I opted for my steel mesh carving glove to avoid any bloodstains. I used masking tape to get a uniform layout and simply removed it when the holes were complete. The best bit is that I now have room for more jaws :) Pictures below show my process...

Very dense foam, easy to cut to shape.

The outline of cut-outs was easy to cut to the correct shape with a clean finish. Adhesion between the layers of the foam was variable. The top layer separated easily but some of the lower layers were difficult to separate and the foam tore between the joins leaving a rough surface which I was able to shave to the required depth with a sharp chisel. I'm not sure how this finish will wear but the foam is doing the job as required now. I'd use this again in preference to pre-cubed foam.

Great material - strong and supportive. It does take a bit of patience to mark and cut through the levels, but take your time and it's well worth the effort. Much more supportive and long lasting than pluck and play foam.

Ich habe den 50 mm dicken Schaumstoff gekauft, um individuelle Einlagen für meine Makita Makpacs zu basteln. Der Schaumstoff ist stabil, aber gut zu verarbeiten – genau richtig für diesen Zweck. Das Anzeichnen der Einlagen hat etwas Zeit gekostet (ich habe mir die Umrisse digital erstellt und auf A4-Klebepapier ausgedruckt), aber danach lief alles problemlos. Wichtig: Das **Herausschneiden mit dem Messer und anschließende Abziehen des Schaumstoffs funktioniert nicht** – die Schnitte werden ungleichmäßig, und eine saubere Tiefe lässt sich kaum erreichen. Mit einer Dekupiersäge klappt es dagegen hervorragend: Konturen aussägen, die Einlage auf die gewünschte Tiefe kürzen (z. B. 20 mm) und zurück in die Matte einsetzen. Am Ende alles fixieren – fertig. Die Matte reicht locker für drei Einlagen. Wer sich die Zeit nimmt und das richtige Werkzeug verwendet, bekommt ein top Ergebnis!

Plaque d'insert en mousse de 70 mm noir/vert, d'acheter pour mettre dans différentes caisse et valise de transport d'outillages, je m'en suis servit et franchement c'est qualitatif, et la matière ce travail plutôt facilement, c'est du solide à côté de cela et propre en tous points. Je recommande.

Muy bien

Prodotto ben fatto e la strtificazione permette un taglio e un risultato davvero perfetti

Perfekt blandning av stabil och mjuk del. Skär ut med laser men var observant på gaserna som är farliga från vissa plastsorter.