1-Pack Black Double Din Radio Install Kit with Wire Harness and Antenna Adapter for Select Chrysler, Dodge, Jeep, Mitsubishi, Volkswagen Vehicles

I fitted into my 2013 Dodge GrandCaravan and also added a rear view camera! Everything works exceptionally well including the factory steering wheel controlI am now Wazing and enjoying my music in my car!!here are my parts used (sorry, being a new user means I can't post any links)0: Atoto A6 2GB/32GB Unit --1. Steering wheel control --2. Rear View Camera --3. Dodge Installation Trim Kit including Antenna adapter4. Soldering iron and solder5. PAC Radio Replacement Interface --6. Trim Panel removal tool --7. Dremel tool set (You need some cutting) --8. Wire stripper --9. Multi meter --10. Electrical tape --11. 3.5MM jack to three pin connector, (look for it in Radio Shack)Now, get to installation,1. pulling the factory radio is pretty easy, you just use the trim removal tool to get the radio panel off and then unscrew the four screws holding the radio in place. Once remove the screws, gently pull the radio out and disconnect the factory harness and radio connector, the radio connector is pretty fragile, be careful not to break it...2. Connect the harnesses, open the PAC harness package, you need to determine which harness to use, for my car, it was the one with slightly bigger connector, try it on the factor harness first. Then lay down the color/wire mapping on your desk and start connecting the wires, PAC did not actually strip the wires so you need to do it, after strip the wires, gently twist so they connect better, then chris cross on with the ATOTO wires and solder the wires on, I like to put my soldering gun under the wire to heat them up and let them soak the solder rather than melt the solder using the iron, better conenction.. After solder, use tape to mask up the bare wires, you will connect all wires except three, the thin Ground wire, KEY 1, and KEY, go ahead and cover up KEY 1, you dont need that . Like picture 13. Wrap the harness, go ahead and wrap the harness so the wires dont go crazy4. Install Steering wheel control (optional), open the PAC SWI unit package, and turn the dial to 7 before you do anything else, TURN THE DIAL TO 7 first. Then connect the 7pin connector (white) comes out from your PAC interface to your SWI unit, go to your vehicle, connect to factory harness and follow instructions from PAC (every car is different, you need to follow the factory instructions) and program it, then use the multiulmeter to find the pins output the resistive differences (this is a bit tricky, my suggestion is to solder wires to each pins on the 3.5mm connector (see pic 2) and then use your multi meter find which two wires output resistive values when you press a button) after you find the two wires, connect them to thin black ground wire and KEY wire (NOT KEY1), and then fire up the ATOTO unit and go to DEFAULT SETTINGS -- STEERING WHEEL CONTROL and see if it registers the presses, if not, swap the wires (because there is no clear way to tell which one is ground...) after you confirm its working, solder the KEY and ground wire5. Placing the antennas, place them anywhere you like, even including inside the radio hole, but I went ahead and place the antennas across the trim and near the wind shield on the driver side so they get better reception.6. Actually installation, because ATOTO is slightly higher than stock unit you need to do a bit cutting, first cut the TRIM Kit side panel about 2mm from both sides, then use Dremel to trim down the top and bottom notch of the stock Trim piece or until it fits7. Back up camera is also fairly easy, hook it up with the reverse light and tuck the cable under the trim and you are good to goHope it is helpful, please leave me a message if you need any help!

Yes, guys I’m talking to you. They don’t put those little fancy instructions in there just for show… Just make sure you don’t make any cuts or change anything about the kit before you read it and everything will turn out just fine. It’s a pretty good quality kit.

Great

I bough this for my Jeep Wrangler unlimited 2014 in conjunction with Boss Audio BVNV9384RC. Both items from Amazon.The wire harness is a time saver and works great (this kit is only for not Alpine factory application). However, I can't say the same for the brackets. They fill the gaps between the factory opening and your aftermarket double DIN radio. But you will need to play with the fitment, use a sander or dremer in order to make it work. Anyways is better than nothing. Making the brackets and radio work together will take a couple of hours if is your first time. But don't worry, is worth it.

Fit my 2012 ram just fine. Comes with an accessory wire (red) that I ran to the left cigarette lighter wires that get power when the key is turned on. Kit fits fine and was easy to install.

I used this for a double din stereo in my Jeep Wrangler. I like that you get a wiring harness and antenna adapter with it, especially considering the price. However the fitment of the actual mounting bracket isn't very good. I had to squeeze it together to get it to fit and once I finally got it all together it looked pretty unprofessional. It'll get the job done by holding the stereo in place but I had to cover it up with a plastic frame around the stereo because I couldn't stand how janky it looked.

Was a great kit for the money. Only negative thing I have to say about it is that I couldn't get my pioneer radio flush with the dash. I had to have it recessed and it looked bad but with some work I could have fixed it. Tip for future installation: use the cigarette lighter for the accessory power for the radio. Just use a piggyback splice and you will be fine.

Changing the radio in my 11 Ram was a nightmare, can't imagine how much worse it would have been without this kid. The harness was perfect and idiot proof. The mounts are a bit on the flimsy side, but once installed you'd never know. For the price, this CANNOT be beat