WITFORMS / Premium Plus - Adjustable AC air Deflector Suitable for Split air conditioners. Enhance Cooling and Heating Circulation

Works great and as described. Easy install.

I was on the fence about buying this product because it seemed pricey, but once out of the box it was very easy to install. I did not have to drill, just placed the all the items like shown in the video tutorial and it was ready. Took me 10 minutes to set it up and it works like magic.

I have a mini split installed in my kitchen and before purchasing this i had to turn it off every time we wanted to have dinner. With this I no longer need to shut it off. Instructions in the box would be nice but i was easily able to put it together by looking at the photos.

Installed on a 24000 BTU unit.Limited instructions and very close tolerance’s make this difficult to install. The pieces that are needed to be snapped together require a lot of hand/finger strength. The installation directions are printed on the back of the box and are very generic. Here are some tips I found useful. Installing the mounting brackets under the mini-split is pretty straight forward. Just slightly lift the bottom of the unit away from the wall and slide the mounting brackets up and under the case. I chose to use 2 special drywall screws to attach the mounting brackets for a stronger mounting point (see pic).So here’s what the manufacturer doesn’t tell you; how to put the rest of the parts together. They just show a single diagram.The deflector shield isn’t like the picture. It’s not slightly s-shaped, it’s just a flat curve. Assembling the deflector shield; there are two pieces on the ends of the shield. They are really hard to snap into place but they will go eventually. Rock them side to side. There is a raised small circle and oval on the bracket, and matching indentations on the air deflector. They can only be put on one way (see pic). The two halves of the shield are held together by two clips. Once installed, the width of the shield CANNOT be adjusted, so before clipping the two pieces together; install the standout arms and measure the distance between them, minus 1/4 inch. Then lay the deflector pieces on a flat surface, overlap them and make the width the same as the measurement you took. Then attach the clips to either side. Again, this isn’t easy and they must be pushed all the way on (see pic).Remove the standout arms from the mounting bracket by sliding the small latches outward (see pic). Then attach the shield the the ends of the arms by pushing the round part of the shield clips into the holes on the arms. They are a VERY tight fit. Now you can finally attach the whole assembly to the mounting brackets. This may be a 2 person job with someone holding up one end while the other is attached.Hope this helps someone.

The design of this item was great. IF THE THE DESIGNER PUT IT IN. I have been in the building tradesfor 30 years , A+B=C if all else is true. I can figured it out with great speed. Now the common guy up on a ladder that said honey hand me the directions, and she says, THERE on the box, WHAT- yea I have to tearbox to give it to you and there not easy to follow, Well ok. So lets get real. you don't type directions on the side of the cardboard box it came in , if it got tore ripped or wet, WELLLL. was it to hard to put it on 1 pc of paper. Other than they should have said your skill level in the tradeds should a 9 or higher to get it up.My skill level is 10 star it took me 20 min most. After cutting the instructions off the box, REAL rookie move to save 1$. in printing. you have the best product of all other on the market. thx 10 Star A buyer

Good and easy to install

This is not worth $55. Keep looking there has to be a better option out there.And the directions are useless.I’m hoping that once I figure it out & everything is in place it will be a little more stable

Our mini split air conditioner blew directly at our sofa where we sit necessitating a lap blanket. With the deflecter installed, the air stream goes over our heads, so no longer need blanket.You can use the mounting bits to clip the deflecter directly to the mini split, but it just seemed simpler, as well as more secure, to use a couple of screws on each side to attach it directly to the drywall.