Diamond Hole Saw

A fraction the price of big box stores name brands and in my opinion work just as well for DIY. For professional repeated use probably not, but I've used mine a few times and still does the job even thru porcelain and ceramic.You can use the tilt technique, or I prefer to make a jig in a piece of 3/4 plywood with a same sized wood hole saw first, then carefully clamp it to my work. If you can't clamp it, have someone hold it while you get it started. A jig can slide a bit on glossy tile, but with practice it's pretty easy to master. You could probably stick on some rubber cement between the two or a self stick rubber pad to keep it from sliding around. You only need the jig to get the full circular cut started, then it's easy to hold in place without the jig in your way. More accurate than tilt method.I use higher speed on tilt method to get cut going. Seems to move around less than on slow speed. Use a little water to cut easier and save the diamond edge.With both methods, I slightly tilt saw from side to side and in circular motion as I'm cutting to keep it cutting thru. Makes a nice clean hole. Be careful of sharp cut edges.

I bought this drill to cut holes in an office desk I bought at a furniture warehouse, so that I could thread my computer wires in from down below the desk, where my outlets are. It's a good product for the price. Worked as well as expected. I'd recommend this product.

Good coating!!! DurableWhy did you pick this product vs others?:Looked ok

Great drill bits for drilling holes in glass for a craft project. They worked very well and held up through quite a bit of use.

When I embarked on the harrowing journey of bathroom renovation, I thought the toughest challenge would be choosing between fifty shades of beige for the tiles. Little did I know, the real test of my DIY mettle would come when I needed to drill a hole through my newly acquired, stubborn-as-a-mule porcelain tiles. Enter the Luomorgo 35mm Diamond Hole Saw - the cape-wearing, laser-eyed superhero of drill bits.The moment it arrived, packaged like the crown jewels, I knew my prayers had been answered. Not only did it promise to glide through porcelain with the grace of a ballroom dancer, but it also boasted the ability to tackle glass, ceramic, and marble - essentially, the Avengers of surfaces. With my drill in hand and the Luomorgo bit attached, I felt like Thor wielding Mjolnir. Spoiler alert: the tile didn't stand a chance.Pros:- Mightier Than Thor's Hammer: This bit goes through tough surfaces like a hot knife through butter, or Thor's hammer through... well, anything.- No More Rusty Business: The nickel-plated surface means it’s more resistant to rusting than my resolve to finish this renovation.- Cuts Like a Dream: The cut was so smooth, my tiles probably didn't realize they'd been drilled until it was over.- Chip Evacuation: The side chip holes ensure waste removal is cleaner than my language when I finally saw the hole.- Wide-Ranging Powers: From glass to granite, this diamond hole saw is like the utility belt of Batman - prepared for any scenario.Cons:- Too Smooth?: The cuts were so effortless, I was momentarily deprived of my DIY war stories.- Addictive: I now wander my house, looking for things to drill holes in. The dog is getting worried.- Water Required: Needs water for cooling, slightly dampening my walk-off drilling fantasies in a cloud of practicality.In the epic tale of my bathroom renovation, the Luomorgo 35mm Diamond Hole Saw emerged as the unlikely hero. Not only did it tackle the daunting task of drilling through porcelain with aplomb, but it also proved itself a versatile tool for a range of materials. It's the Batman of my tool belt, the Thor in my toolbox. With its sturdy build, rust resistance, and smooth cutting capabilities, this diamond hole saw is a must-have for any DIY-er facing their own home improvement odysseys. Just remember to add water and proceed slowly – patience, young Padawan, the Luomorgo does not disappoint. Now, if you’ll excuse me, I’m off to drill holes in everything... responsibly, of course.

This is a quality drill bit for the money . I couldn’t believe how expensive these bits are in the big box store and I refused to pay $80 when i only needed to drill 1 hole through tiles. The speed and drill accuracy of this bit blew my mind ! It cut through the 2x4 tile like it was butter !

Good value cuts fast.

This is not 3 inches. This is 75mm. They are NOT equivalent and you should not sell them as such. I took the listing at face value when I ordered it, and the hole is just barely too small for the project intended. Thankfully I didn't cut into the final material with it first.Sell metric, or sell imperial, don't market as both.