KnuKonceptzKnuKonceptz Kord Kable 14 Gauge Copper Speaker Wire Cable - 100 Feet

Arrived fast, great quality, recommended by specialist

This cable is properly spooled so it doesn't twist as it comes off the roll.Jacket is soft but durable, strips easily and cleanly and the copper strands are uniform, high gauge and feathery when touched on end.Sound is good for regular general listening applications. Definitely recommend this over a number of other brands I've tried here that are twisty with brittle jackets and very rigid copper strands.

Rewired new Elac Debut B6.2 Rear surround sound bookshelf speakers in my new 5.1 set up. The rear speakers are powered from an Emotiva Integrated 50 watt per channel 20 hz-20 khz wired from the pre-amp output of a new Yamaha 7.1 Surround sound receiver. I ran a test stereo only signal into the amplifier CD input via an AudioengineUSA aptX B1 Bluetooth receiver. The sound of the music was immediately clearer, fuller and with better dynamics. Instruments and vocals became more distinct and became better defined.The Knu Konceptz Kord 14 gauge speaker wire outperformed my 30 year old solid 2C #16 twisted copper wire which I have used for many sound systems over the years.I then had enough wire from the 100 ft run to rewire the left ,right and center Elac Debut 6.2 matching speaker set.The surround sound improvement was heard immediately ( temporarily disconnected the subwoofers to only hear the newly wired set up ).Not only did it immediately sound better, the many fine #36 AWG OFC strands tightened into the FosPower speaker Bannana Plugs without having to retighten the connectors.I re-ordered another 100 foot run to re-wire my 2.1stereo Wharfedale Diamond 225 speakers. These speakers were Bi-Wired from my 100 watt/channel Balanced amplifier. As this set up is higher end equipment the improvement in sound was more noticeable. Highly recommended.

I bought 2x100ft of this wire to replace my previous wiring about 1-2 months ago. Been putting off installing it cause of work and being busy, but also felt like the current sound was okay and I wasn't expecting that much of an improvement.Boy was I wrong. Replacing the previous wires (Amazonbasics 16 gauge i believe) with these pure copper 14 gauges wires sounds like taking a blanket off the speakers. What blew me away the most was not just the clarity at high volumes, but the clarity and waaaaaay better separation of frequencies at low volumes. I don't know if it's the improved inductance of the wires, but my receiver (a Yamaha 7.1 unit) sounds so much better. Since I got this Yamaha receiver I've thought the bass sounded flubby on it compared to the Onkyo receiver it replaced.... but i didn't think of the speaker wire, which I also replaced at the same time. This wire puts it on another level and really pushes it beyond the old Onkyo unit. Even with having a subwoofer, some low frequencies still inevitably bleed into the other speakers (as they should IMO, i want a sub supplementing the bass, not taking over all low frequencies, that would be terrible)....and this is where I really notice these wires shining. Put simply, they've adjusted the sound just enough that everything gels together way better than before. I love it.The quality of the wires is impeccable. The plastic is strong, bends nicely, weighty, yet extremely easy to work with. This specific gauge works perfectly with Fospower banana plugs. I can't recommend KnuKonceptz copper wire enough.

Extremely flexible cable. Looks good and clean. Sounds very good. Don’t waste money buying expensive cables but don’t cheap out by buying copper clad aluminium cables. Overall, very good. The only thing that annoys me is when I try to remove the insulation with a cable stripper, even by using the hole for the 10 awg, some strands are cut off. (Could be the tool and not the cable.)