Electrically Conductive Paint 50ml - Water-Based Carbon Coating for Guitar Shielding, PCB & Remote Control Repair - Matte Black EMI/RF Shield

Super Product for Repair to your Faulty Remote Controls.. Thank You..

I bought this to shield the cavity of a guitar I was building. I bought this because of the quantity available in one pot.The problem is it never sets!This means it continues to generate carbon dust after it had dried, its goes everywhere! Onto fingers, hands work top, all of which transfer to the grain of my guitar! Once in the grain it does not come out!The electrical conductivity after 2 or 3 coats was around 30ohms....So, it works but is simply not suitable for a guitar cavity.It paints on like water, not like paint , drys quick enough but leaves a dust film.I have had to seal the surface with poly to prevent further marks.

I used this product to completely revive two tv remote controls that no longer worked properly. On one of them, the power button no longer worked, on the other there were other buttons that were dead.All you need to do is carefully dismantle the remote, and then use a cotton bud to paint some of the liquid onto the black underside of the rubber buttons of the remote. It dries within a minute. Then reassemble and the remote works again.It can also be used on rubber keypads that rely on conducting keys.Truly a great, versatile product.

Me get be my fault with regards to application (I only did one coat which covered the cavity walls) but when dry it’s really dusty and when fitting switch your fingers end up covered in black dust.Obviously this dust is conductive so now I’m trying to diagnose and suss a reoccurring switch issue, which may be due to the dust getting into the switch

The paint quality is okay and dries quickly, but it might not be suitable for all purposes, as the paint is not durable enough for my needs because it doesn't stick for long. However, it is still good for most of the intended purposes. The bottle has enough paint to apply if it comes off. I also tested it on a TV remote, and it worked fine on the rubber one but did not properly stick on plastic.

I don't like that the bottle is shaped more like a hip flask so easy to topple over (don't tell me how I know), and also the consistency is quite liquid. This was used to shield an electric guitar and it took a few coats, but there's more than enough for many coats for a typical Strat body and from testing with a multimeter everything showed good connectivity. It is also easy to clean up afterwards with a bit of naptha, though I suspect the coating is going to be a bit fragile. But once under the pickguard it shouldn't move at all.

Good for small electrical repairs such as worn pads - be aware that it has high resistance so it it won't work to repair long traces. Dries quickly.

This stuff is just rubbish its just carbon powder in water , to call it a paint is ridiculous once dry it just wipes away , it doesn't set at all or stick to any surface . I sent this back , Buy a different one.

Die Infrarot-Fernbedienung an meinem alten Samsung-Gerät reagierte anfangs nur schlecht, am Ende gar nicht mehr. Ich habe sie zerlegt, die Kontakte auf der Platine mit Isopropanol gereinigt und dann die entsprechenden Gummikontakte mit einem Wattestäbchen mit dieser Farbe bestrichen. Nach ca. 30 Minuten Trockenzeit wieder zusammen gebaut und siehe da: das Ding funktioniert wieder wie neu. Bin schon ganz schön begeistert das es vor allem so einfach war.

Terrible product, applied on a guitar electronic cavity using instructions, have let it dry for over 24 hours and the product stains everywhere making impossible to install electronics.UPDATE: the paint also provided grounding issues when electronics installed. Had to sand most of it off to resolve.NOT RECOMMENDED

Werkt perfect om kleine reparaties aan printplaten te verrichten. Bijvoorbeeld door waterschade of lekkende batterijen. De sporen kunnen eenvoudig opgeschuurd worden en gerepareerd met deze geleidende lak. Zorg voor een heel klein kwastje!

Worked perfectly to repair a keyboard with keys that weren’t working.

Excellent produit sans prétention. Non, ça ne remplace pas une vraie piste cuivre sur de grandes distances, mais sur de courtes ou modérées distances, pour des courants faibles, sur un contact souple de télécommande, ça marche très bien et facilement. Le fait que le solvant soit de l'eau, que ça sèche rapidement, que ça puisse se passer au pinceau fin ou au rotring ou à la plume en font un produit génial et très économique, avec lavage à l' eau des instruments