Impresa Urethane Band Saw Tires - 2 Pack - Fits 14 x 1 x 095-Inch Saws - Great for Metal and Wood Cutting - Compatible with Most Bandsaws - No Adhesive Needed

Some people commented that these tires were too wide for their bandsaw wheels. They fit fine on my Jet JWBS-14CS 14" bandsaw. The bandsaw wheels are curved instead of being flat so the tires are made to basically snap in on the sides of the wheel. They are (by design) a challenge to get on the wheels but I warmed them up next to a heater prior to installing and was able to stretch them onto the wheels. My rubber tires lasted 12 years before one broke, I expect these being urethane will last me a lifetime. Saw runs fine with new tires, no vibration or balance issues. They are a good value for two tires compared to some other ones I look at. Recommended.

I bought these to replace the original ones that came in my machine. These work great. Good fit and work super.

No issues installing it and can’t see any wobble in the blade. Highly recommended for the price.

Bought these for a 15 year old Delta 14" bandsaw. Read all the hype about difficulty installing and watched several videos. On arrival I had the wheels prepped and ready to go. Bolted one to the workbench. Stepped in the tire and gave it a few good tugs to stretch it out. Clamped on wheel in two places and proceeded to stretch it on bare handed. Fit perfectly. Ran a round screwdriver under the tire around the wheel a couple of times and done. 10 mins max for both. Time will tell about quality and longevity, but install was a breeze.

Installation is difficult. Soften it in boiling water (not warm water). Use your hand and foot to stretch it. Then be prepared to still apply significant force to install the tire on the wheel. I mostly installed it, put each palm on it and used my thumb to push it on. There is a lip on the wheel rim. I used a small screwdriver to get under it and then push it over the lip. You'll see. But my refurb is done. Works great again. Should have been done 10 years ago.

I like not having to use any adhesive to install them! As for 'ease of installation, ( not so easy)But the instruction say to soak the belts in hot water for a little while and try to install them while they are still warm and flexible! Well I did all that and it still was a fight to get them installed on the wheels of my band saw. But hey, taking the good and the bad, it is a verygood product. and they fit perfectly on the 14" wheels of my band saw. If ever needed again, I would buy them in an instant!

Love these tires. They were so easy to install. Used 2 zip ties and a pice of pvc pipe with a screw driver. 5 minutes per tire install.

Installed in about 15 minutes with a method found on youtube using a dowel in a drill with a dowel in the chuck to roll around the wheel and move the tire into place. My saw required another person to stabilize the wheel as it turned. Product seems good. I replaced a similar poly tire I have used for 18 years. No vibration and sound reduced from older tire. Cutting sample wood at 90 degrees was perfect with no scarring of material. Back cut vibration test showed no vibrations. Would recommend for now but will see how long it lasts.

As part of a face-lift on my 14" Delta 28-274c, I put these new tires on. Granted, the old ones were in pretty bad shape, but now the bandsaw is quieter, better tracking, and less vibration just as advertised.I warmed them up in hot water and they went on fairly easily. I used a clamp, then worked it over the wheel with a pair of screwdrivers as you would a car tire onto a rim.

Buena calidad, a la medida

Fitted these as a replacement tires my wheel was 14 1/4 " so a little bit tight . Followed a post on you tube by Tim B on fitting using a drill to stretch the tire as it is fitted no soaking in hot water or soap required. It worked for me took about 30 mins for both wheels. Look it up. As for the tires seem to be ok time will tell how durable they are.

Once properly warmed up the bands went on easily and once cool were very secure.

As the title suggests, follow the directions and boil these to soften them up enough to stretch. A 2nd set of hands will help get them on, l didnt have that option. They do have to fit tightly anyway but they fit and woek as intended.