44pcs Cutting Wheel Set Compatible with Plastic for Rotary Tool, HSS Circular Saw Blades 6pcs, Resin Cutting Discs 20pcs, 545 Diamond Cutting Wheels 10psc with 2 Screwdrivers

Good quality, durable, time-saving, long-lasting, easy to use, sharp blades, cuts through most surfaces, variety of uses, very effective, shipped fast, and reasonably priced for quantity.

Nice set only one problem but the little screw driver helped to fix it. The holes in black cut off wheels to small for the collet screw. If you take the little screw driver and work it through the cut of wheel it expands the hole enough for screw to g through.

I purchased this product to cut through a thing sheet of stainless steel. Even though the product wasn't listed as being able to cut through steel, the 22 mm disc managed to cut through the sheeting I was working on. It did take a bit longer than I had hoped and the edge left behind wasn't straight though. For the purpose of the job, it did had a satisfactory result. For the amount of product you receive, the price is quite good as well. I would be careful with the larger diameter saw blades. When I attached the 55mm saw blade and turned my Dremel to the 4th speed, the entire blade began to wobble and almost flew out of the Dremel. Resecuring and turning the Dremel to the 1st speed was just fine though. Considering that the larger diameter saw blade can spin at higher RPMs at a lower speed, it should have no problem cutting through softer materials but I would warn against using it above a 2 or 3 on your machine. I do appreciate the variety and number of cutting options provided and the included screwdrivers were helpful since you don't need to have your own smaller flat head. However, there are only two of each saw blade so be careful if one breaks or gets dull. You can burn through the blades pretty quickly. Pros: Large variety of cutting wheels and discs Lots of extra discs in case on breaks Cons: Larger diameter cutting wheels don't stay secured in my model of Dremel Only two of each cutting wheel diameter

I only bought this for the resin cutting discs (the black ones). I used it to cut through rusted exhaust fasteners where an angle grinder would be too big/unwieldy. I used this kit with Harbor Freight's "1.3 Amp Variable Speed Rotary Tool Kit". To get an idea of what I had to cut through, I cut the following: 1. Cut straight through steel M10 exhaust studs to lop them off completely. I had to do two of these. 2. Cut a few sides off of steel M10 nuts so I could remove the nuts from the studs. This is for when the nut is so deformed and dissolved due to rust, that neither a regular nor extractor socket could be used. Just cut off a side or two, the nut's clamping power will be relieved then the remnants of the nut can be popped off the threads sideways/perpendicular to bolt's length, with a hammer and chisel. I had to do this with three nuts and these discs. 3. Cut straight through flat 1/2" wide stainless steel exhaust clamps holding heat shields on, the nuts and bolts holding the heat shields on were too far gone to get any type of socket on, had to do about six of these. I used a single resin disc to cut through all of those. For the price I was expecting rotten quality: discs exploding on me, wearing down really fast, flying off mandrels, etc. Instead I only needed to use one disc for all of it, the mandrel didn't fail or loosen, by the time I was finished the disc was barely worn and still usable. The performance for the price was great and a nice surprise. I intend to continue using it until that disc fails which is probably not going to be any time soon. Having the ability to cut through metal with such small discs is very handy. Cutting straight through an M10 exhaust stud took about one minute, without applying any pressure either just let the speed do the work, make sure you wear safety squints, gloves and block the sparks if necessary, may want to wear a mask with a particulate filter too, otherwise you can taste the dust lol. Everything in the kit comes in a handy vinyl pouch with see through plastic pockets to organize the contents. I put the resin discs in a separate zip bag with a silica gel packet to keep it free of moisture and avoid water or atmospheric humidity from degrading the resin over time, though they're so small that even if they did come apart mid-cut I doubt they'd do any damage, at least unlike a 4-5 inch angle grinder wheel coming apart at 11000rpm LOL...

I bought this 44‑piece kit to tackle a variety of little woodworking jobs around the workshop, and it’s turned out to be exactly what I needed. The set includes a handy assortment of 6 mm‑10 mm cutting wheels for a rotary tool plus six high‑speed steel (HSS) circular saw blades in common diameters. Versatility: The cutting wheels slice cleanly through thin plywood, hardwood trim, and most plastics (acrylic, PVC, polycarbonate) without chipping. The HSS blades stay sharp for the usual 1‑2 mm cuts on a small bench‑top saw, making finish work and detail trims a breeze. Quality: All wheels are made from thin‑wall carbides that stay true to shape at high RPMs, and the HSS blades have a reinforced tooth geometry that resists dulling. I’ve run them for hours on a Dremel‑style rotary tool and a mini‑circular saw with no wobble or vibration. Convenient Packaging: Each size is clearly labeled and stored in a sturdy, reusable case, so you can grab the exact wheel or blade you need without rummaging through a junk drawer. Value: At this price you get more than enough variety for hobby‑level cabinets, model‑making, DIY repairs, and hobby‑craft projects—far cheaper than buying each piece separately. The only minor quibble is that the smallest 6 mm wheel can be a touch fragile if you force it into very hard metal, but for the intended wood‑and‑plastic work it’s perfect. Overall, the 44‑piece cutting‑wheel and HSS blade set is a reliable, cost‑effective addition to any small‑shop toolbox. Highly recommended for anyone who needs precise, fast cuts on wood, plastic, or light metal without investing in a full‑size industrial set.

I dont have micrometer, but I feel the shaft is a tad to small. I put it in my Drexel, tighten it up all the way and I try cutting with it the shift is loose and vibrates out. I can't even make a single cut.

Works as expected

Perfect for the small cutting jobs. Blades are good quality. An they last for several cutting jobs as long as not a big task.

لابأس

Bought these cutting wheels to do little jobs here and there. So far, I've tried all these wheels on Dremmel to cut wood, metal and plastic, they worked fine. Might try on glass project at a later time.

تحل بعض المشاكل للمحترفين