Lisle 49960 Pneumatic Tool Holder

I had made a similar item for my air tools but this is nice the locking bar is nice to prevent tools from falling. It works well to hold the tools.

I normally throw all the pneumatic tools in the bottom drawer of the toolbox. This thing is great mounted it to the side of the toolbox and hang everything there for a quick access and better organization. It's made out of some very thick metal so I have no doubt it's going to hold up with all the stuff I have hanging off of it. The lock feature works great none of the stuff falls off. If you have some cheap crappy airline fittings you may have an issue but all the ones I have are no problem.

I've got two of these and they're worth every penny! The organizer holds 5 air tools and has a sliding lock. The tools won't fall out of my rolling tool cart. There's a hole where you can slide a lock through to keep your air tools "safe" when you're not around. Obviously locks only keep honest people honest. The locking feature can be easily bypassed - it's basically just sheet metal afterall. The locking feature keeps your tools from falling out of the organizer when moving the cart over rough floors too. It's a very very good organizer and I definitely recommend it.

This is a lot smaller than pictured

Sturdy and I’m sure the lock feature will loosen up over time and use. Ideally one of the slots would be offset for larger tools, but getting all the little stuff out of the way makes room for the big tools elsewhere.The lock feature can be bypassed by unscrewing the fitting from the tool, but how often is that going to happen?Can’t do much about it, but leaving the air opening ‘up,’ where dust and the law of gravity conspire to get into air tools is about the only flaw.

I use Milton high flow fittings and they would not fit in the slots. I had to file the slots about 1mm so they would be wide enough to accept my tools. Once that was done it works great.

Surprised at how small it was..I drilled 2 holes in my new 5 drawer cart, bolted it in and took everything out of 1 drawer and put it in this holder. Regained a drawer.Easy to put tools in and out. No grease inside my drawers (now). Strong enough to hold a lot of weight for how small it is.Lock is very usefull to keep tools from falling out as the cart is moved around. No point on a toolbox.. waste of money but on a cart that is moved a lot. It keeps the tools in place.I see no point to put a lock on it. It's true use is to keep everything in the rack and not on the floor.

3 Words! MADE IN USA! I’ve been at this since the 1970’s! I’ve noticed that my tools made in the USA, Germany and Taiwan have outlasted all others. Just MATTER OF FACT. Taiwan has done incredible Chrome plating and metal work. Probably because they aren’t affected by the EPA. Another note is I’m still using 1/4” NPT with my compressor from the 1990’s and a regulator. Pneumatic tools are engineered with 1/4” NPT so I see no reason to change to “High AF” fittings. I set my Regulator to REGULATE THE CORRECT amount of AF and have the same pneumatic tools (except a butterfly impact which air-bladder blew out) for DECADES. As stated on Pneumatic “Oil Daily”. A couple of drops goes a long way. Brass Nipples are still the best. This is a fine product from a very reputable company.UPDATE: (3) Round Neodymium Magnets (Not “Rare Earth”) and I hung 1/2” Drive etc. across with no problems or slipping!!! Put your spare round NEO Magnets under your oil filters on your vehicles, lawn mower, tractor etc. CAREFUL! They can cause blood blisters and DO NOT USE if you have a pacemaker!!!Please CLICK HELPFUL! Thanks kindly!

Sturdy enough for 2 air wrenches, die grinder and air ratchet

Holds 4 impact guns no problem. Surprisingly strong

Have a tool cart at work and i spending so much time digging through air tools on top of those sockets i need and get very frustrated when i cant find something. I was either going to make something to hold all my air tools but just do not really have the time to make one so decided to find something. This looked so promising online before i purchased, the picture makes it look way bigger than the product actually is. I thought the price was reasonable and decided to buy it because the concept looked promising. The box this arrived in was very small as i thought it was going to be bigger than what it was. The tool is quite simple, has five slots and the air tool fitting slides into those slots and the red slider, slides back and forth to lock them in place. At the right side is a hole for a lock which prevents it from sliding. Mounting it to a tool cart is pointless cause someone could just steal the tool cart or just remove the unit itself. Mounting to a bench would make more sense. The unit itself is good qaulity as it holds my 1/2'' impact, 3/8'' impact, air hammer, and die grinder without it bending. I ended up mounting it to my tool cart with hardware not supplied. Overall i think it's a good idea, wish it was longer and bigger. You need really small bolts for the holes on the unit unless you enlarge them. I attached a few pictures of an idea. Does what i want it to and overall happy with it.

J'adore dommage que le prix a remonter en flèche sinon il en aurais d autre en commande

Solid made in the USA product